5.0/ 5.0
100% pembeli merasa puas
4 rating • 2 ulasan
5(4)100%
4(0)0%
3(0)0%
2(0)0%
1(0)0%
Atur jumlah dan catatan
Stok Total: 67
Subtotal
Rp30.000
PWM to Voltage converter Module 0%-100% to 0-10V digital analog PLC
Rp30.000
- Kondisi: Baru
- Min. Pemesanan: 1 Buah
- Etalase: Semua Etalase
Description:
The PWM transfer voltage module LC-LM358-PWM2V converts the PWM digital signals into 0 to 10V analog signals.
It can be used as signal interface switching for PLC or other industrial control boards. The output voltage is regulated by adjusting the duty ratio of the PWM. The modules are small in size and easy to use in different places.
Features:
- MCU embedded technology
- Easy to operate, fine tuned by potentiometer
- Select the PWM signal input level range through short-circuit
- The module is smaller, easy to carry and use
Parameters:
- Work Voltage: DC 12V-30V (> 100MA)
- PWM Receiver Frequency: 1KHZ-3KHZ
- PWM signal input level range:
* The peak of 4.5V to 10V level. The short cap install in 5V. This level is used for normal controller or 5V MCU;
* The peak of 12V to 24V level, so inserted in 24V. The short cap install in 24V. This level is used for normal PLC controller.
- Conversion range: 0%-100% PWM to 0-10V
- Allowable error: 5%
Package Included:
- 1 x Module
Wiring Instruction:
- VCC: To Working Power Supply
- GND: To Power Supply Ground
- F: To Input Frequency Pulse Signal
- GND: To Input Ground
- VOUT: To Output Related Voltage
- GND: To Output Ground
Attention:
- The module shares ground.
- Connect working voltage to VCC and GND. Reverse connection is not allowed to avoid damage to the board and device.
- Connect frequency pulse signal to F. And there will be related voltage output in VOUT terminal
- Relationship between input and output: 100Hz = 1V. 1KHz = 10V.
- The accuracy of this module is 1%. It is not for uses needing higher accuracy.
- When there is bias of related relationship, use on-board potentiometer to calibrate.
Hardware Interfaces:
- VCC: Working Power Supply DC 12V-30V
- GND: Working Power Supply Ground
- PWM: Input Signal PWM +
- GND: Input Signal -
- VOUT: Output Voltage 0-10V
- GND: Output Voltage Ground
The PWM transfer voltage module LC-LM358-PWM2V converts the PWM digital signals into 0 to 10V analog signals.
It can be used as signal interface switching for PLC or other industrial control boards. The output voltage is regulated by adjusting the duty ratio of the PWM. The modules are small in size and easy to use in different places.
Features:
- MCU embedded technology
- Easy to operate, fine tuned by potentiometer
- Select the PWM signal input level range through short-circuit
- The module is smaller, easy to carry and use
Parameters:
- Work Voltage: DC 12V-30V (> 100MA)
- PWM Receiver Frequency: 1KHZ-3KHZ
- PWM signal input level range:
* The peak of 4.5V to 10V level. The short cap install in 5V. This level is used for normal controller or 5V MCU;
* The peak of 12V to 24V level, so inserted in 24V. The short cap install in 24V. This level is used for normal PLC controller.
- Conversion range: 0%-100% PWM to 0-10V
- Allowable error: 5%
Package Included:
- 1 x Module
Wiring Instruction:
- VCC: To Working Power Supply
- GND: To Power Supply Ground
- F: To Input Frequency Pulse Signal
- GND: To Input Ground
- VOUT: To Output Related Voltage
- GND: To Output Ground
Attention:
- The module shares ground.
- Connect working voltage to VCC and GND. Reverse connection is not allowed to avoid damage to the board and device.
- Connect frequency pulse signal to F. And there will be related voltage output in VOUT terminal
- Relationship between input and output: 100Hz = 1V. 1KHz = 10V.
- The accuracy of this module is 1%. It is not for uses needing higher accuracy.
- When there is bias of related relationship, use on-board potentiometer to calibrate.
Hardware Interfaces:
- VCC: Working Power Supply DC 12V-30V
- GND: Working Power Supply Ground
- PWM: Input Signal PWM +
- GND: Input Signal -
- VOUT: Output Voltage 0-10V
- GND: Output Voltage Ground
Ada masalah dengan produk ini?