4.5/ 5.0
75% pembeli merasa puas
4 rating • 1 ulasan
5(3)75%
4(0)0%
3(1)25%
2(0)0%
1(0)0%
Atur jumlah dan catatan
Stok: Habis
Subtotal
-
Smart Electronics LCD Module Display Nokia 5110 for Arduino
Rp32.500
- Kondisi: Baru
- Min. Pemesanan: 1 Buah
- Etalase: Mikrokontroler
Smart Electronics LCD Module Display Monitor Blue backlight adapter PCB 84*48 84x84 lcd 5110 Nokia 5110 Screen for Arduino
Specification
Note:
· LIGHT linkedwith GND, the backlight to be lit.
· Need you to compress the screenand PCB tighter, might got loose after the delivery.
· Use a 3.3V controller, otherwise the display could be quite vague.
LCD5110 Module:
Power supply voltage:
2.7V-3.3V,5Vis OK,but part of the screen becomes black when tested
Data interface level:
2.7-5V
Backlight power supplyvoltage : highest 3.3V
Module size: 43.6mm x 43.1mm(width X height)
Installation diameter : 2mm
Backlight:
White
· RST--------- Reset?
· CE------------ Ship selection?
· DC----------- data/commands choice
· DIN----------- Serial data line?
· CLK------------Serial Clock Spee
· 3.3V------------VCC?
· LIGHT--------- Backlight Control Terminal
· GND----------- Power Negative
Features
· 84 X 84 dot matrix LCD,can show 4 lines of characters
· Use serial interface communicate with themaster processor,the number of interface signal line reduced greatly, only 8 signal lines including power and GND.Support different types of MCU,such as the SPI,MCS51 serial mode 0 of AVR.Transfer rate up to 4Mbps,can full speed write display data without waiting time.
· Can use the conductive glue to connect the module with the printed board,without connecting cable.The metal hooks on the module can fix the module on the printed board,which is very easy to install and replace.
· LCD controller/driver chip has been bound to LCD chip,the volume of LCD is small
· Low power supply,the working current in normal situation is lower than 200μA,and has power-down mode
Specification
Note:
· LIGHT linkedwith GND, the backlight to be lit.
· Need you to compress the screenand PCB tighter, might got loose after the delivery.
· Use a 3.3V controller, otherwise the display could be quite vague.
LCD5110 Module:
Power supply voltage:
2.7V-3.3V,5Vis OK,but part of the screen becomes black when tested
Data interface level:
2.7-5V
Backlight power supplyvoltage : highest 3.3V
Module size: 43.6mm x 43.1mm(width X height)
Installation diameter : 2mm
Backlight:
White
· RST--------- Reset?
· CE------------ Ship selection?
· DC----------- data/commands choice
· DIN----------- Serial data line?
· CLK------------Serial Clock Spee
· 3.3V------------VCC?
· LIGHT--------- Backlight Control Terminal
· GND----------- Power Negative
Features
· 84 X 84 dot matrix LCD,can show 4 lines of characters
· Use serial interface communicate with themaster processor,the number of interface signal line reduced greatly, only 8 signal lines including power and GND.Support different types of MCU,such as the SPI,MCS51 serial mode 0 of AVR.Transfer rate up to 4Mbps,can full speed write display data without waiting time.
· Can use the conductive glue to connect the module with the printed board,without connecting cable.The metal hooks on the module can fix the module on the printed board,which is very easy to install and replace.
· LCD controller/driver chip has been bound to LCD chip,the volume of LCD is small
· Low power supply,the working current in normal situation is lower than 200μA,and has power-down mode
Ada masalah dengan produk ini?