5.0/ 5.0
100% pembeli merasa puas
1 rating • 1 ulasan
5(1)100%
4(0)0%
3(0)0%
2(0)0%
1(0)0%
Atur jumlah dan catatan
Stok Total: Sisa 1
Subtotal
Rp650.000
Lemon Rx DSM2 Compatible 8-Channel Receiver + Satellite
Rp650.000
- Kondisi: Baru
- Min. Pemesanan: 1 Buah
- Etalase: LEMON-RX Product ( DSMX / DSM2 )
Specification :
Type: DSM2 Compatible 8 Channels Full Range Receiver (All Channel Failsafe with UART output)
Number of Channel: 8
Modulation: DSM2 Compatible
Band: 2.4 GHz
Dimension: 25(L) x 18(W) x 11(H) mm
Weight: 12.0 gram without satellite
Voltage Range: 3.45 - 7.2V
RCgroups discussion
http://www.rcgroups.com/forums/showthread.php?t=1773138
manual :
http://www.lemon-rx.com/shop/documents/Lemon%20RX%20manual.pdf
Binding (1) Setup
Video:https://www.youtube.com/watch?v=FZsHGEW2zPY&feature=youtu.be
1) Insert bind plug to the receiver.
2) Provide power to the unit.
3) Enable bind mode in transmitter and ensure distance separation of 2 meters from receiver.
4) Remove bind plug.
Binding (2 - Enable 11ms frame rate for high speed digital servo) Setup
1) Insert 2 bind plug to the receiver binding location.
2) Provide power to the unit.
3) Enable bind mode in transmitter and ensure distance separation of 2 meters from receiver.
4) Remove bind plug.
5) Every time when the units are powered, quickly flashing green light indicates 11ms frame rate is enabled.
Setting Failsafe
Step 1: Start by binding the receiver to the transmitter in the normal way.
Step 2: Proceed as follows to set failsafe (see video: https://www.youtube.com/watch?v=FyW1v12dv_k)
1) Ensure that transmitter and receiver are turned on.
2) Insert bind plug into the receiver (Note: to set failsafe, bind plug is applied only when the receiver is turned on).
3) Set transmitter controls to the desired failsafe positions.
4) Press the side pushbutton to memorize failsafe settings.
5) Observe that the green light at the end of the receiver turns on to indicate failsafe is set. (Repeat step 4 will cause the LED to turn off which means failsafe is disabled).
6) Remove bind plug.
7) Disconnect the power for at least 2 seconds and then reconnect the pow
Type: DSM2 Compatible 8 Channels Full Range Receiver (All Channel Failsafe with UART output)
Number of Channel: 8
Modulation: DSM2 Compatible
Band: 2.4 GHz
Dimension: 25(L) x 18(W) x 11(H) mm
Weight: 12.0 gram without satellite
Voltage Range: 3.45 - 7.2V
RCgroups discussion
http://www.rcgroups.com/forums/showthread.php?t=1773138
manual :
http://www.lemon-rx.com/shop/documents/Lemon%20RX%20manual.pdf
Binding (1) Setup
Video:https://www.youtube.com/watch?v=FZsHGEW2zPY&feature=youtu.be
1) Insert bind plug to the receiver.
2) Provide power to the unit.
3) Enable bind mode in transmitter and ensure distance separation of 2 meters from receiver.
4) Remove bind plug.
Binding (2 - Enable 11ms frame rate for high speed digital servo) Setup
1) Insert 2 bind plug to the receiver binding location.
2) Provide power to the unit.
3) Enable bind mode in transmitter and ensure distance separation of 2 meters from receiver.
4) Remove bind plug.
5) Every time when the units are powered, quickly flashing green light indicates 11ms frame rate is enabled.
Setting Failsafe
Step 1: Start by binding the receiver to the transmitter in the normal way.
Step 2: Proceed as follows to set failsafe (see video: https://www.youtube.com/watch?v=FyW1v12dv_k)
1) Ensure that transmitter and receiver are turned on.
2) Insert bind plug into the receiver (Note: to set failsafe, bind plug is applied only when the receiver is turned on).
3) Set transmitter controls to the desired failsafe positions.
4) Press the side pushbutton to memorize failsafe settings.
5) Observe that the green light at the end of the receiver turns on to indicate failsafe is set. (Repeat step 4 will cause the LED to turn off which means failsafe is disabled).
6) Remove bind plug.
7) Disconnect the power for at least 2 seconds and then reconnect the pow
Ada masalah dengan produk ini?