5.0/ 5.0
100% pembeli merasa puas
1 rating • 1 ulasan
5(1)100%
4(0)0%
3(0)0%
2(0)0%
1(0)0%
Atur jumlah dan catatan
Stok Total: Sisa 8
harga sebelum diskonRp25.000
Subtotal
Rp24.250
Sensor MQ-4 MQ4 Methanes Gas Metana CNG sensor module Arduino
Rp24.250
diskon 3%
Harga sebelum diskon Rp25.000
- Kondisi: Baru
- Min. Pemesanan: 1 Buah
- Etalase: Sensor
MQ-4 Methane Gas Sensor Module MQ 4
MQ-4 Methane Gas Sensor Module MQ 4
Sensitive material MQ- 4 gas sensors used in clean air, low conductivity tin oxide (SnO2). When there is an environment in which the combustible gas sensor, conductivity sensor with increasing concentration of combustible gases in air increases. Use simple circuit can convert the change in conductivity of the gas concentration corresponding to the output signal. MQ-4 Methane gas sensor of high sensitivity, propane, butane and has a good sensitivity. The sensor can detect a variety of combustible gases, especially natural gas, it is a low-cost sensor suitable for a variety of applications.
Features:
++ Using high-quality dual-panel design,with power indicator and TTL signal output instructions.
++ The switching signal having a DO (TTL) output and analog output AO.
++ TTL output valid signal is low. ( Low-level signal when the output light can be directly connected to the microcontroller or relay module )
++ Analog output voltage with the higher concentration of higher voltage
++ Has a long life and reliable stability
++ Rapid response and recovery characteristic
++ Input voltage : DC5V Power consumption ( current ): 150mA
++ DO output : TTL digital 0 and 1 ( 0.1 and 5V)
++ AO output :0.1-0 .3 V ( relative to pollution ) , the maximum concentration of a voltage of about 4V
Wiring:
++ VCC: positive power supply (5V)
++ GND: power supply is negative
++ DO: TTL switching signal output
++ AO: analog signal output
Special note: After the sensor is powered,needs to warm up around 20Sec, measured data
MQ-4 Methane Gas Sensor Module MQ 4
Sensitive material MQ- 4 gas sensors used in clean air, low conductivity tin oxide (SnO2). When there is an environment in which the combustible gas sensor, conductivity sensor with increasing concentration of combustible gases in air increases. Use simple circuit can convert the change in conductivity of the gas concentration corresponding to the output signal. MQ-4 Methane gas sensor of high sensitivity, propane, butane and has a good sensitivity. The sensor can detect a variety of combustible gases, especially natural gas, it is a low-cost sensor suitable for a variety of applications.
Features:
++ Using high-quality dual-panel design,with power indicator and TTL signal output instructions.
++ The switching signal having a DO (TTL) output and analog output AO.
++ TTL output valid signal is low. ( Low-level signal when the output light can be directly connected to the microcontroller or relay module )
++ Analog output voltage with the higher concentration of higher voltage
++ Has a long life and reliable stability
++ Rapid response and recovery characteristic
++ Input voltage : DC5V Power consumption ( current ): 150mA
++ DO output : TTL digital 0 and 1 ( 0.1 and 5V)
++ AO output :0.1-0 .3 V ( relative to pollution ) , the maximum concentration of a voltage of about 4V
Wiring:
++ VCC: positive power supply (5V)
++ GND: power supply is negative
++ DO: TTL switching signal output
++ AO: analog signal output
Special note: After the sensor is powered,needs to warm up around 20Sec, measured data
Ada masalah dengan produk ini?